MOCpages : Share your LEGO® creations
LEGO models my own creation MOCpages toys shop Gundam RX-0 UnicornMecha
Welcome to the world's greatest LEGO fan community!
Explore cool creations, share your own, and have lots of fun together.  ~  It's all free!
Gundam RX-0 Unicorn
The gundam unicorn, From sunrises new series of movie, Gundam Unicorn. Lets start off with basic information. Approx. building time 6 hours. Height 16 in. Date created august 3. Equipment, rifle, shield, 2 beam sabers, and a booster pack (no I don't feel the need to add official names and numbers.) Pilot Banagher.
About this creation

Lets start with a 360 view, shin front

Shin side

Shin back

thy front

thy front armor movement

Torso

Torso with open cockpit

Torso back with twin beam sabers and pack

Head front

Head side

Head back

Now all the boredom is over, time for action poses!

Sweeeeeeeet

Coolest gundam shield ever...

RATE AND COMMENT...OR ELSE(lol)

and of course his gun.

The gundam was a lot easier to build than I had originally expected. Just about every surface on it is flat, so it really adds a streamline look, all the brick studs make things look too blocky. In real life the Gundam looks almost exactly like the model(except maybe the head)but my photo taking skills aren't so great, just note that in real life it is about 5 times better than it appears here. If you'd like any other gundams made I'd like to hear your suggestions.

1000 views!!! never thought that would happen.

I may redo this in LDD or build an SD version of it.



Comments

 I made it 
  April 1, 2012
Quoting Jared . Hm, can't believe I missed this. The proportions are excellent, and that shield IS pretty awesome. Have you been thinking about doing anything from the new Gundam AGE series yet, like maybe AGE-1-Spallow?
Well I've only seen the first few episodes of gundam AGE, as I prefer UC series, but if I get further into the series and if I am inspired perhaps.
 I like it 
  April 1, 2012
Hm, can't believe I missed this. The proportions are excellent, and that shield IS pretty awesome. Have you been thinking about doing anything from the new Gundam AGE series yet, like maybe AGE-1-Spallow?
 I made it 
  December 17, 2011
Quoting Pete Corp Bold attempt.
Thanks, not quite there yet design wise though.
 I like it 
  December 16, 2011
Bold attempt.
 I like it 
  September 28, 2010
Neat build! The proportions look accurate!
 I like it 
  August 9, 2010
they are easily some of the sturdiest pre-made joints out there. The only thing that really outperforms them are the joints that use technic gears. But I wouldn't worry yourself about those just yet. I don't want to sound like one of those people on MOCpages that is all like "look at my stuff", but this might help you out if you want to make a mech that uses those type of joints. http://www.mocpages.com/moc.php/145503
 I made it 
  August 9, 2010
Thanks, I was thinking to get some, because those look pretty sturdy.
 I like it 
  August 9, 2010
In answer to your earlier question: the click joints for the knees on my second generation frame are made of two of the following pieces: Technic Rotation Joint Disk with Pin Hole and 3L Liftarm Thick stuck together. The sets that these can be found in are: 7470-1 Space shuttle discovery (1), 7671-1 AT-AP Walker (2), 7721-1 Combat Crawler X2(2), 10186-1 General Grievous (2), 10174-1 Imperial AT-ST UCS (4), 7706-1 Mobile Defense Tank (4), 8996-1 Skopio XV1 (16), 7701-1 Striking Venom (8), 8694-1 Titanium Command Rig (2), 4483-1 and 4483-2 AT-AT (8), 4482-1 AT-TE (6). Keep in mind that most of these sets are discontinued and are expensive. It is much easier to purchase them on bricklink. http://www.bricklink.com/catalogItem.asp?P=44224 is the link. Keep in mind that when I say that there are 8 in a certain set, remember that you need TWO to make one joint, so the number of complete joints you get in a set is half of what I mentioned above. Hope this helps
 I like it 
  August 9, 2010
Hey man! Great work on this. I like all the detailing on it. It was well worth the wait.
Marcus J.
 I like it 
Rick .
  August 8, 2010
hi. thanks for your comment. I will build the whole body, but it wil take a long time. I'm glad to meet another Gundam Fan. Gundam Unicorn is a very nice Gundam, and you did a good job. it looks very nice. About your photo skills, try to avoid taking pictures from the front. you should turn your camera 45 degrees, then it might not look so 2d. trust me. 'D Rick
 I made it 
  August 8, 2010
Quoting Rick . hi. thanks for your comment. I will build the whole body, but it wil take a long time. I'm glad to meet another Gundam Fan. Gundam Unicorn is a very nice Gundam, and you did a good job. it looks very nice. About your photo skills, try to avoid taking pictures from the front. you should turn your camera 45 degrees, then it might not look so 2d. trust me. 'D Rick
Will do, thanks
 I made it 
  August 6, 2010
Quoting Ryan Tennant This is fantastic :) It's huge!
Thanks
 I like it 
  August 6, 2010
This is fantastic :) It's huge!
 I made it 
  August 4, 2010
The first time I tried the torso I could get it to function, but it didn't look good at all, so it is really just trial and error when it comes to that.
 I like it 
  August 4, 2010
whoa it looks huge. Iv always tried making a Gundom but for some resons I can never make the torso right.
 
By Marcus J.
Add to my favorite builders

12
people like this. See who.

4,757 visitors
15 comments
Added August 4, 2010
 


LEGO models my own creation MOCpages toys shop Gundam RX-0 UnicornMecha


You Your home page | LEGO creations | Favorite builders
Activity Activity | Comments | Creations
Explore Explore | Recent | Groups
MOCpages is an unofficial, fan-created website. LEGO® and the brick configuration are property of The LEGO Group, which does not sponsor, own, or endorse this site.
©2002-2014 Sean Kenney Design Inc | Privacy policy | Terms of use