Normandy SR2 (second version) Instructions: A LEGO® creation by Mark N. : MOCpages.com

Normandy SR2 (second version) Instructions

Rate it

Add a comment

Zoom in

ATTENTION: The picture above is an older model of the Normandy, and is NOT the final product of this guide.

About this creation

This is a guide for anyone who wants to build my Normandy SR2, requested by Donald Hallama (You should check out his large scale Normandy)

Start with this piece...

Add two skeleton arms (these are the old ones from the Castle sets)

Place on a 3x2 flat

Put a white 4x2 flat here

Place these flat pieces on top

Add an 8x2 underneath

Place a 2x2 here...

...then a black 1x2 flat and orange 1x2

Put this piece on top

Add a 6x2 flat

Then get these three pieces...

...and place them here

Add these flat pieces here

Next, place 4 of these connecting piece on a black 2x4 flat

It should be able to fit nicely under the pieces you just made...

Then put this piece on the end

Note: you can use a 6x1 flat instead of a 2 and 4x1 flats.

Put these pieces on the back

Then add this piece...

...and finish with two 2x1s (again, you can use a 4x1 if you want)

Get a 4x1 flat and 3x1 flat

Connect with 2x1 and 4x1 (or 6x1) flat

Place on top

Tuck in a black 3x1 flat

Then add a 4x1

And finish with a 4x1 topped with a 2x1 smooth

Complete with an 8x1 smooth

Make two of these

Attach by the middle of this black piece...

...like so

Then attach the back of the ship with the front

Get a 4x1 flat

Add another

Then a smooth

Finally add one of these slope pieces

This should fit perfectly on the front of the ship.
Now the main body is done!

For the wings, first place a black triangular piece along side one of these connecting pieces

Then join with a white

Note: For the following component, make 4

Add to the wing

Then add a 2x2 flat

Add these

Get a 2x1

Then add this white 4x1.
You can use a normal 4x1, or you could even make your own decal

Then add a black grate piece

Place on the wing

Place this piece, with another black grate on top

Add another engine underneath (For that grey piece, you can use a black one, I just didn't have enough)

Underneath, add a 4x1 here

Then attach a grate piece where the 4x1 sticks out.

Once you've made both wings (Completely identical) you only have a few more steps to go...

Get this piece

Then add this rail piece

Next, assort this bricks like so. If you want, you can use a normal 1x2 instead of that one at the bottom, I just had to use that because of the stand I made

Finally add these sloped pieces on top

Lastly, add these pieces to the other side of the double-sided stud brick.

Place this under the ship

Finally, add the wings. There you have your own miniature Normandy SR2! I left out the stand since it would be pretty pointless to include it, and you might want to make your own custom stand anyway.

Comments

Add a comment

I made it

Mark N.

December 4, 2012

Quoting Donald Hallama Thanks! I'm working on it as time allows (digging for pieces takes a while) I've decided to build the ME3 rev. (Blue) due to the colors that I've been able to scrounge up. It's a fun build.

No problem. Glad I could help :)

I like it

Donald Hallama

December 3, 2012

Thanks! I'm working on it as time allows (digging for pieces takes a while) I've decided to build the ME3 rev. (Blue) due to the colors that I've been able to scrounge up. It's a fun build.

By Mark N.

Add to my favorite builders

person likes this. See who.

269 visitors
2 comments
Added December 1, 2012

Instructions (3)

You are at the beginning of this folder.