MOCpages : Share your LEGO® creations
LEGO models my own creation MOCpages toys shop HK416D14.5RS [v6]Military
Welcome to the world's greatest LEGO fan community!
Explore cool creations, share your own, and have lots of fun together.  ~  It's all free!
HK416D14.5RS [v6]
About this creation

Created: 7/9/2008 | Last Update: 9:00 PM 7/9/2008

Finally! Version 6 on file. I improved this thing a whole lot. The biggest improvement is the FULLY RETRACTABLE STOCK. Yes, many have been able to do this, but how many have the stock retract and still have the bolt carrrier assembly fit into the stock? Hoorah!

You may notice a missing trigger. This is because I am trying to get a working trigger on it and to say that there's more to come.

I have and idea: if you can spot any minor or major improvements since the previous versions that I have failed to mention, say so in your comment and I'll add it to a list of viewer-spotted improvements.






Comments

 I like it 
  April 28, 2009
What do you do when you don't like the gun you have? build a better one out of lego's, hk416 has always been one of my favorite guns...
 I like it 
  November 9, 2008
Hey,this gun is very nice,but all of your 416's look very much like each other. I can't see any difference between them all,but the difference are there,i just can't see them. I won't give you five smileys,because it can't shoot. But,if you would make a firing mechanism in it,i won't look so good as now. However,nice job. Please review my M-14 assault rifle,or please try to make a Thompson m1921. Thanks,Lawrence.
 I made it 
  September 27, 2008
Eric Stevens: Which model of the Sten are you building? Mark I, I*, II, II (Canadian), III, IV, V, VI or a suppressed variant? I'm looking into how the bolt works on the Sten models and I might be able to adapt my HK416 bolt design to fit the Sten type bolt.
 I like it 
  July 22, 2008
Hey, no problem, I can't wait till V8!
 I made it 
  July 22, 2008
Alexander, you are right. Here's the thing: the placement on the upper reiever was correct, but the placement near the back of the grip was wrong. That means the upper receiver was too short and two studs too far forward. I have a completed version 8 with that change, along with many other changes. Thank you so much for pointing that out.
 I like it 
  July 22, 2008
You sure? take a look at the HK-pro page, it looks like it's in the same place as the M4-M16-AR15 reciever pin, which is farther back. It could be that is a ilusion from the Legos.
 I made it 
  July 15, 2008
Christian, version 7 has the rail on the top and bottom with a more accurate placement of the vents. It'll be a little while for the rest of the v3 instructions because I have to label them and organize a ton of photos. Thanks!
 I made it 
  July 14, 2008
Paul N., the upcoming instructions will actually be of the final version, whichever that will be (currently working on v7). I am actually planning on selling the instructions. I'm going to try to post the rest of v3's instructions that I have. I had to hold off on the others due to school and work.
 I made it 
  July 14, 2008
Alexander, the rear retaining pin is in the correct spot for the HK416D10RS, which should be the same as the HK416D14.5RS. I have an image of the D10RS field stripped and it matches up.
 I made it 
  July 14, 2008
Joe M., I used a 1:1 scale printout of the HK416D10RS to build version one. For latter versions, I just improved off the original creation. This one is the HK416D14.5RS and I went back to the 1:1 computer version for the improvements from v5.
 I like it 
  July 12, 2008
wow!!!! but are the instructions gonna be for this version (v6) of your gun, or for the older version?
 I like it 
  July 12, 2008
Man, this is SWEET! The only problems I can spot are: The Rear retaining pin is to far forward. AND there is no selector switch. Also there is no mag release. nor is there any bolt catch. (That I can see, as all your pictures are of the right side) and one last thing, can you fold down the front sight? But other than that this is GREAT!
 I like it 
  July 10, 2008
Did you use a 1:1 Scale Printout like the BAR? I do not know why the person below me has given this a 4 out of 5. Keep up the amazing work.
 
By PyBrick Replicas
Add to my favorite builders

21
people like this. See who.

2,844 visitors
13 comments
Added July 10, 2008
 


LEGO models my own creation MOCpages toys shop HK416D14.5RS [v6]Military


You Your home page | LEGO creations | Favorite builders
Activity Activity | Comments | Creations
Explore Explore | Recent | Groups
MOCpages is an unofficial, fan-created website. LEGO® and the brick configuration are property of The LEGO Group, which does not sponsor, own, or endorse this site.
©2002-2014 Sean Kenney Design Inc | Privacy policy | Terms of use