MOCpages : Share your LEGO® creations
LEGO models my own creation MOCpages toys shop Pieces I Wish LEGOŽ Would Make pt.3Digital LEGO
Welcome to the world's greatest LEGO fan community!
Explore cool creations, share your own, and have lots of fun together.  ~  It's all free!
Pieces I Wish LEGOŽ Would Make pt.3
Part three of however many. Most of these parts were made by request. Please be sure to check out the previous entries. Made in Autodesk Inventor 2008 using real LEGOŽ dimensions.
About this creation
On top this may look like an ordinary tile...

...but it's actually 4x4. I think they need to make tiles that cover more surface area. That way you could avoid a lot of crevaces on your tiled surface.

Brently Mills and Mark Kelso suggested I make a tiled wing. So here is a prototype 4x10, smooth, left-hand wing.

The bottom isn't very complicated, but if LEGOŽ built one, it probably would be.

This piece is similar to the exsisting 1x1 circle, except without the stud on top.

This is a handy little number! It's a half-studded/half-tiled plate! My inspiration comes from 4-wide cars. Because at some points I've had to make smooth wheel arches. This was hard because the smooth tiles stretch back, usually underneath the cabin of the car, so my windows (1x1 slopes) could not be attached on the outside. With these, the base of the windows would be connected and the plate over the wheels will be smooth. Understand? I didn't think so.

Here's is the bottom of the piece. Notice how the bottom even looks like I morphed the two together.




Comments

 I like it 
  August 22, 2014
Again, They made the 1x1 flat round tile. And again, I have some models to show you with that part in use. I'll even show you that uses all the LEGO parts that you wanted made that are in existence.
 I like it 
  July 21, 2012
They made the flat stud
  December 9, 2010
They should make these pieces.
 I like it 
  June 20, 2010
tiled wings! You woulda' thought they woulda' thought of this by now!
 I like it 
  August 8, 2008
there all ood part ideas. how about an inverted 1 by 1 slope to be used for 4 wide fenders
 I like it 
  July 19, 2008
Another great list of pieces.
 I like it 
  July 18, 2008
i guess these pieces are commonly wanted because i've wanted them too.
Dylan Denton
 I like it 
Heather Braaten
  July 17, 2008
I was just wishing for the 4x4 tile and studless 1x1 round yesterday! I love to see your ideas every time. And the fact that you've rendered them in 3-D with such detail just really brings them to life!
 I like it 
  July 17, 2008
yeah!! they should make these!! your missing one, a 2x1 plate with a slanted edge. that would be sweet!!
 I like it 
  July 17, 2008
Dude you forgot one of the most important! 1x1 grills!
 I like it 
  July 17, 2008
Yes, your ead my mind! You have no idea how much I've been annoyed when I have a tiled a surface and I want a circular 1 1 plate. Good day
 I like it 
  July 17, 2008
They are great ideas but if LEGO were to make a smooth stud it would get stuck on the thing you put it onto.
 I like it 
  July 17, 2008
i like the wing, the 4x4 tile, and the studless circle! we NEED THOSE PIECES!!
 I like it 
  July 17, 2008
I agree,the studless circle is a must-have!an I love the wing,we really need that!
 I like it 
  July 17, 2008
good ideas i wanted a roud brick with studs on both sides
 I like it 
  July 17, 2008
Yes i totally agree with the small studless circle! We really need them!
 I like it 
  July 17, 2008
Ooooo, very tempting, Shadow...but too much utting-cay of the ego-lay is baaaaad ju-ju! And when I die, I want to go to Lego heaven, not that other place!
 I like it 
  July 17, 2008
oh yes! I would love the first part! It is,actually,possible to make these! on the wing,(ill make it for ya mark ;P)you just take one of the same with studs on and cut them away with a knife. then it will be like this one. it works.
 I like it 
  July 16, 2008
Wow man, all of your concept pieces are great! My favorites are the reverse tile, the studless 1x1 round, anf the 1x1 axel. Keep this up. Oh, and you should get one of those 3D printers to actually make these. That would be awesome, you could start your own company! Ok, I got carried away, still, I love these. Nice work. Peace - Patrick
 I like it 
  July 16, 2008
Wow, taking requests...my thanks! Now if only you were in charge of parts at Lego headquarters we'd all be in ABS heaven!
 I like it 
  July 16, 2008
Heh heh, you might not be able to make it with the program, but it would be cool if lego made a mohalk piece for minifigs,:)
 I like it 
  July 16, 2008
haha 1st review!
 
By Dylan Denton
Add to my favorite builders

39
people like this. See who.

4,649 visitors
22 comments
Added July 16, 2008
 


LEGO models my own creation MOCpages toys shop Pieces I Wish LEGOŽ Would Make pt.3Digital LEGO


You Your home page | LEGO creations | Favorite builders
Activity Activity | Comments | Creations
Explore Explore | Recent | Groups
MOCpages is an unofficial, fan-created website. LEGO® and the brick configuration are property of The LEGO Group, which does not sponsor, own, or endorse this site.
©2002-2014 Sean Kenney Design Inc | Privacy policy | Terms of use